Category: Heating and Air Conditioning
The other day, I was cleaning his house when I found a one-inch piece of charcoal burnt into one of my couch cushions! It came from a piece of wood that popped from my fireplace to the couch. While all that little chunk of ember did was burn a hole in the furniture, my house could have gone up in flames! I am thankful that all I have to do is turn the couch cushion around to hide the burn mark!
Most home fires happen during the winter months than any other time of year, when the cozy warmth of a fireplace is at its most inviting. Not only are fires a danger, space heaters are often used to heat rooms that need an extra boost; plus, home heating devices can produce an abundance of deadly carbon monoxide gas.
Seniors aged 65 and older are three times more likely to die or be injured in a house fire than other age groups. Not only that, but if you live in a newer home, reports are saying you may have less time to escape a fire because of synthetics. Here are some important home heating safety tips to remember:
1) Check Your Chimney and Fireplace for Hazards
Have the chimney flue pipe checked each year if you or your loved one uses a wood-burning fireplace. Make sure that there is a screen or glass in front of the fireplace to catch any wild sparks or moving logs. Keep flammable objects such as stockings and curtains away from the fireplace when in use.
2) Get the Proper Fire Extinguisher
Get an ABC multipurpose fire extinguisher for your home, read the manual so you and your loved ones know how to use it, and store it in a place where it is easily accessible in case of a fire. OSHA gives some helpful tips for the workplace, hut they can apply to your home as well.
3) Check On Smoke and CO Alarms
Make sure each room has a smoke detector, especially the kitchen, living room, and all places where it’s most likely a fire will start. You need CO detectors outside each sleeping area, so they can wake you up in the event of a carbon monoxide outbreak; CO is at its most deadly when you are asleep since you are not alert to get out of the house. Check all smoke and carbon monoxide detectors and make sure all batteries have been replaced. Install additional detectors if you find areas without them.
4) Remember Space Heater Safety!
Remember that space heaters need space! Anything that can burn should be kept at least three feet away from the heater. If you’re looking to buy a new space heater get one that automatically shuts off if the heater falls over in case of an accident.
Many homeowners tend to completely forget about their furnace maintenance until the weather starts to turn cold again. Once the chilly night hits, many people directly start using their heating machines without any monthly cleaning. One of the biggest mistakes that people usually make is to seek yearly maintenance during the peak time of the season when the others are also likely to be in the same boat. In that case, you not only need to wait for the technicians for a long time but it’s also a great chance to get low-quality service.
In order to avoid such inconvenience, you can learn a few DIY tips that enable you to maintain your furnace without waiting for the technicians:-
1. Check The Filters Of Furnace
Usually, all heating systems have two air filter- one is located at a center place near to thermostat and another is fitted somewhere inside the furnace near the blower component. Both the filters need to be cleaned frequently to avoid accumulating dust around the unit that increases the chance of damaging valuable parts. When your systems are not in use, dust builds up easily in the internal parts of the machine despite packing it properly. Around every three months, it is important to clean your machine to improve its work efficiency.
2. Spot Check The System
Once in a month, you should randomly check your systems especially when they are not in use to avoid major furnace repair issues. Inspect the air intake coming from outside and the exhaust on your roof to ensure that there is no leaves or frost built up around the ducts.
3. Give The System A Trial Run
In order to avoid such costly furnace repair bills, it is important to give the system a trial run before the cold sets in. Check your filter and the system as instructed above and then flip on the system and observe its performance. You can diagnose the flame elements through the side panel to determine whether they are heating up properly or not. It should look evenly blue and nice. Also, notice that system should cause any rattling noise when you switch on the unit.
Maintain your furnace by considering these things as this will allow you to avoid costly repairing cost and ensure the efficient performance during the peak time of summer season. All these tips are easy and simple to follow.
If you have a functional furnace in your house, it may need repair from time to time. As a matter of fact, furnaces can stop working any time. However, when they do, you don’t have to panic as you can do the basic repair on your own in most cases. Given below are some DIY repair tips that may help you get your thing back on the track once again. And you won’t need to call a professional. Read on.
1. Change the filter
The filter plays a big role in any furnace, especially during winter when it is under heavy load all the time. When the filter gets clogged, the airflow becomes poor. So, we suggest that you change the air filter at least once every 4 months. However, you may also want to consider the manufacturer’s recommendations.
2. Check burner flames
Make sure the flame is blue and burns evenly. A yellow flame means that the burners are dirty; however, it may also mean that there is carbon monoxide. If the later is the case, you should get in touch with a professional.
3. Vacuum the burners
First, you should switch off the system and the gas supply. Next, you should vacuum the dirt or dust close to the burners and blower compartment.
4. Clean the blower and flame sensor
Make sure you also clean the blades of the blower using a good vacuum cleaner and a brush. You should be careful not to damage the wiring or counterweights. For the flame sensor, you may want to try an emery cloth. It is designed for cleaning metal surfaces.
5. Dust surface igniter
You can use a drinking straw for removing dust from the surface igniter or the pilot. Just don’t touch that hot thing.
6. Look at the drive belt
Actually, you should check it on a regular basis. It is not costly to replace, though. A new belt won’t cost you more than $5, give or take.
7. Lubricate bearings
You should check the blower shaft bearings and the motor bearings for lubrication. Ideally, it’s a good idea to lubricate them on an annual basis. You can use lightweight motor oil.
8. Deal with the corrosion
If you can see a powdery substance on the vents of the exhaust, know that it can be corrosion. You can’t do anything about. So, calling a professional is a good idea.
9. Leaky vents
During your inspection, if you notice a leak, you can use seal them up with heat resistant silicone or metal tape.
10. Check exhaust pipes for air intake
You should check the exhaust pipes for air intake. If there is debris, leaves or ice, you should remove it from the exterior of the exhaust.
Long story short, if your furnace is not working properly, you can check it thoroughly with the help of the tips given in this article. After you have checked the furnace and have followed the given tips, your furnace should work properly. If it doesn’t, you should call a professional.
Oil burners in fuel are an integral part of oil heating appliances. In the oil boiler, the burner must be adjustable, depending on the changing parameters of the fuel oil. See what are the most important things related to oil burners.
The advantage of oil boilers is that after replacing the burner, the oil furnace can also be operated as a gas. There are also produced dual-fuel burners enabling the change of fuel from oil to gas and vice versa, without the need to replace the burner. However, due to the high price, they are rarely used in boilers intended for single-family houses.
Oil Burner and Gas Burner in heating boilers sprays fuel oil or allows it to evaporate. During this process, the fuel intensively mixes with the air and only a mixture of oil and air is burned.
A proper oil quality is a prerequisite for the proper operation of the oil burner. The most important for the course of the combustion process is kinematic viscosity. To get the right viscosity, you need to heat the oil. In the burner, the oil is heated by an electric oil heater. It is integrated with the nozzle and has a variable power range. The heater adjusts its electrical power to the instantaneous heat demand, thanks to which it minimizes the amount of energy consumed. After the fuel has reached a predetermined temperature, e.g. 80 ° C, the thermostat gives a signal to the controller. The controller first starts the fan, then the ignition system, and then opens the shut-off valve for the oil supply. The resulting oil-air mixture ignites, as indicated by the flame detector.
If the flame disappears during the burner operation, the oil supply is immediately interrupted. The device attempts to restart the burner and ignite the mixture. However, if the mixture does not ignite at the programmed time, the burner will be blocked.
After starting and adjusting the burner, the control electronics allow you to set the minimum amount of oil consumption. If the oil flow is reduced (for example, by 10% due to a blocked nozzle), a service inspection signal will appear on the display.
In order to achieve total and energy-saving combustion, the burner must be perfectly matched to the boiler. Otherwise, the boiler will have lower efficiency, and hence – will use more oil to produce the same amount of heat.
Oil burners – types
Fan burners can be one- or two-stage. In boilers with one-stage burners, the capacity change occurs by turning the burner on or off. Boilers with two-stage burners on the first stage work with less power, on the second – with nominal. Two-stage burners ensure more economical operation of the heating system. Rebar Bender is equipped with a security system controlling the system operation, and in the event of a malfunction, switching off the burner and shutting off the fuel supply.
A two-stage burner better than a one-stage burner. A properly selected oil burner guarantees durability and high boiler energy efficiency as well as minimizing pollutant emissions.
Industry and family gatherings cannot do without cooking, parties and other forms of home entertainment. The latest trend is to bristle firewood in the fireplaces and outdoor ovens for warmth and red spirited fun. In summers you can cook and bake without making your home hot and uncomfortable, and in winters you can bathe in the cozy warmth of the crackling fireplace. The home and yard can be used creatively for a number of barbeques and get-togethers. All you have to do is keep well stocked on firewood.
Different ignition levels of different firewood:
Trees give firewood that is the ideal environmentally friendly fuel source in today’s times.
Why should firewood be used?
Firewood has carbon neutral burning properties as compared to coal and foreign oil. When it is burnt it releases carbon-dioxide but in the same amount as produced in a natural environment. There is no way that burning firewood contributes to global warming in the environment. Firewood is eco-friendly and economical when it is purchased in bulk quantities and can help lower utility costs.
Is coal good for burning?
Coal is also used as a heat source because it burns steadily well and is compact. But coal has pollutants that release carbon dioxide emissions. Firewood has much lesser carbon dioxide emissions and pollutants in comparison, which is why it is a better option than coal.
Firewood burns at different temperature levels
A Firewood company will have documented burning properties of different varieties of firewood for sale. The burning property of this fuel source helps in controlling temperature of the fire. The firewood for sale has different moisture levels that can be tested and calibrated so that they can be dried until they can be ignited properly.
There is a variety of soft and hardwood that is available in the market. You can choose the variety you desire by checking out its ignition quotient and checking its documented information. There is firewood which catches fire immediately and there are others that can stay smouldering for a long long time. Check out the wood you want according to your needs and specifications.
Where can you find firewood?
To find out the best places, where you get good quality firewood for sale, just type “Firewood near me”, on the search engine, your location will be assessed. You can get the best outlets dispensing different types of firewood like Box firewood, ironbark firewood, red gum firewood, seasoned hardwood, mixed eco-friendly firewood. Firewood is easily accessible and the best eco-friendly fuel that can be safely used in your homes.
Purchase good quality firewood in shape you desire:
Well reputed companies dealing with firewood, employ trained and proficient staff members to assist you in your purchases. You can get the forest firewood shaped into blocks or long logs according to your needs. Let the flickering flame of fire crackle brightly in your fireplace.
Firewood can be contaminated and for this, you need to choose “your personal” clean and a good lot from a well-reputed seller like the family-owned Black Forest Firewood. The wood purchased from Black Forest Firewood is sustainable and has undergone the tough Trommel screening procedure so that it stays contamination free.
1. Wood burning stoves are cost-effective. Unlike other home heating technologies that cost a fortune to purchase and maintain, wood stoves let you pleasantly heat your home without adding to your monthly expenditure. The price of wood stoves can’t compare with even the cheapest electric and gas heating system in town. The price of wood fuel is almost 10% lower than the price of oil, electricity, and gas.
2. They are the most flexible and versatile choice of home heating systems. They can perfectly fit almost everywhere in your house as long as there is adequate spacing to safely and seamlessly install the vent pipe. So, with wood stoves, you can zone-heat everywhere in your house regardless of the size and shape of the room.
3. Wood fuel is proven beyond any reasonable doubt to be carbon neutral. Unlike the common belief amongst peers, wood burning doesn’t increase atmospheric carbon dioxide levels. Though wood logs will obviously emit carbon dioxide while burning, the carbon discharged will be counterbalanced by the growing trees. This is a fact since trees absorb carbon dioxide and emit pure oxygen which aids minimize the levels of carbon dioxide released into the atmosphere.
4. Wood offers a renewable and sovereign source of energy. Wood fuel is available in plenty and there are lower chances you can lack ready wood fuel for sale. As for oil and gas, they are non-renewable so you can expect them to run out any time without prior warning. As for electricity, it is produced by burning fossil fuels which a limited commodity meaning it can run out any fine day.
5. Wood fuels produce more and exceptional heat. They run on the radiant heat principle so they heat rooms a bit more proficiently and rapidly compared to heat produced via vent systems. Wood stoves produce heat that radiates through both tops and all sides of the unit hence sending warm to all directions in the target rooms.
6. Works perfectly as a real cooking stove. Some modern wood burning stoves are designed to work as cooking stoves. All you need is to install the cookware and adjust the temperature and you are good to go. With a good wood burning stove, you can thus reduce your expenditure on cooking gas.
7. Current-day wood burning stoves come in a plethora of wonderful finishes, styles, and sizes. They are designed with your lifestyle and preferences in mind. Almost all modern wood burning stoves are perfectly designed and stylishly finished to meet the special decor and style preferences of different homeowners. That said when shopping, you can be sure to find a good stove that has an inflection best suited for your home decor and style.